Showing results: 46 - 57 of 57 items found.
-
Quantic PMI
PMI offers custom surface mount (SMT) and QFN packaging for many types of devices. SDLVA's, Log Amplifiers, Phase Shifters, Attenuators, Switches, as well as Low Noise Amplifiers. PMI also offers multifunction options in a single QFN package such as Limiter / LNA or LNA / Detector. PMI has the experience to offer custom devices that meet your specific control function at high frequency. Mounting and integrating high frequency RF devices take skill and experience such that the package itself does not degrade the RF signal. PMI has the experience in selecting the proper package, integrating the RF devices and providing the required testing.
-
Analog Devices Inc.
Analog Devices voltage variable attenuators (VVAs) ensure accurate control for a wide range of applications. Our absorptive VVAs are ideal for designs where an analog dc control signal controls RF signals levels over a 30 dB amplitude range, while our monolithic VVAs feature low insertion loss, high IP3, and wide dynamic range, as well as a balanced topology that delivers excellent return loss.
-
Keysight Technologies
The Keysight RF and Microwave multiplexer modules for the 34980A Multifunction Switch/Measure Unit offer broadband switching capabilities for switching from DC to 26.5 GHz. Use these modules to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. A switch/attenuator driver module also allows control of switches and attenuators external to the 34980A Mainframe.
-
FSMR3000 -
Rohde & Schwarz GmbH & Co. KG
The R&S®FSMR3000 is a microwave measurement receiver to calibrate signal generators and attenuators with one single instrument. Most important features provided are tuned RF level measurements, level measurements, analog modulation and spectrum analysis. Additionally, the R&S®FSMR3000 can be equipped with powerful hardware for high-end phase noise test supplementary to the standard phase noise test with the spectrum analyzer.
-
Teledyne Defense Electronics Relays & Coax Switch
- Fully customized switching configurations (from 1x1024 to 24x42)- Universal Power Supply (96-240Vac)- Local Display – High Visibility LED- Standard 19" racks and custom chassis available - Local and/or remote control- 50 and 75 ohm impedances- Multiple interface configurations: - RF ports – SMA, 2.92mm, N, SMB, TNC, etc. - Control – RS-232, Ethernet, USB, Keypad, etc.- Monitor cycle count- Full Command API included- In-circuit programming (firmware upgradable) - Systems can be ruggedized and tested for challenging environments- Passive components Integration (Filters, Attenuators, Dividers, Combiners, etc.)
-
Teledyne RF & Microwave
Microwave Solutions is a worldwide leader in the design, development, and manufacture of RF and microwave components. Our broad line of components operate in the 100 kHz to 26GHz range and include Attenuators, BAW Devices, Detectors, Isolators and Circulators, Linearizers, Mixers, and VCOs. For over 50 years our components have played key roles in sophisticated airborne and satellite communications equipment, navigation and guidance systems, radar and sonar equipment, telemetry electronics, surveillance, and reconnaissance systems, and high performance commercial test equipment.
-
TYPE ATF -
National RF, Inc
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Pickering Interfaces Ltd.
Our LXI modular chassis are available in 7-slot or 18-slot and support over 1,000 of our PXI modules, additionally our 2-Slot USB/LXI Chassis allows most of our 1 or 2-slot PXI modules to be controlled via USB or Ethernet. These range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of T&M modules such as programmable resistors, digital I/O, power supplies, battery simulators and attenuators.
-
Pickering Interfaces Ltd.
Our LXI modular chassis are available in 7 and 18-slot and our LXI/USB modular chassis are available in 2, 4 and 6-slot and support over 1,000 of our PXI modules. The PXI modules supported range from: PXI general purpose relays, matrices, multiplexers and RF switches to special PXI switching functions such as fault/signal insertion. Also supported are a selection of simulation modules such as programmable resistors, digital I/O, power supplies, thermocouple simulators, function generator, battery simulators and attenuators. This gives you enormous flexibility to define a switching or T&M system to exactly match your needs.
-
NEXUS-4 -
Quintech Electronics and Communications Inc.
The NEXUS-4 is a bi-directional fully non-blocking 3232 RF matrix switching system that can route any input ports to any outputs in a 6 RU chassis. With the frequency range of 700 MHz to 4 GHz and the capability of expanding to 256256, it enables large scale wireless testing that involves many MIMO base stations and devices. The built-in programmable attenuators and efficient automation interface provide ease-of-use testing of signal fade and emulation of mobility scenarios. It can dramatically increase lab efficiency by eliminating manual patch panel and cabling as it can be remotely reconfigured for different test setups consistently in seconds.
-
SA1001H -
Hangzhou Softel Optic Co., Ltd.
*SA1001H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network.. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network*It is more convenient for debug engineering debug, because of the plug-in diplexer filters with built-in adjustable equalizers, adjustable attenuators, plug-in output splitters and scientific and reasonable ports for online test.*These equipments will work in the field rugged environment for a long time continuously, because of the aluminium alloy casing, good heat dispersing performances, beautiful looks, dependable linear power supply and lightning protection systems.
-
LDA-602EH -
Vaunix Technology Corporation
The LDA-602EH has a large attenuation range of 120 dB with an exceptional 0.1 dB step size, allowing for both precision and accuracy during fading tests or device characterizations. This attenuator also features a fast 15 us switching speed, an operating temperature from -30oC to 50oC, a maximum RF input of +28 dBm, and is priced at $875. The LDA602-EH operates with a low insertion loss of 9 dB to 6 GHz, an input IP3 of +55 dBm and a typical VSWR of 1.3:1. Easily programmed for ATE applications, the LDA digital attenuators are a cost effective solution whether you are in engineering, the production test lab, or in the field. Units are ROHS compliant and can be used with any PC or laptop computer with USB 2.0 port (or powered USB hub) and Windows operating system. Lab Brick Signal Generators are provided with easy to use Lab Brick GUI software, 32 and 64 bit API DLL files, LabVIEW and Linux compatible drivers.
